How to reset a schlage keypad lock

Whether you’re moving into a new home, need to reset your existing lock, or even if you feel like changing the current password for any reason; it’s important to know how to reset a Schlage keypad lock.

This lock offers the convenience of not needing to carry a physical key and provides greater security as a bonus. Proper resetting your Schlage keypad lock is easy and will ensure your home is always safe.

Encoding a Keypad Lock:

Before moving toward the method of resetting the Schlage keypad lock, let’s have a look and discuss the encoding of the keypad lock. There are 2 most common types of keypad locks; DE265 and BE468.

Difference between DE265 and BE468:

DE265 Keypad Lock Encoding:

To encode this type of lock, the user will need to have the three-digit factory code that came with the lock when it was purchased. To begin encoding the lock, enter the factory code followed by the “#” key.

Then enter your desired four-digit user code twice (for confirmation), followed by the “#” symbol again. The last step is to press “*” which will save the new user code in memory and exit programming mode.

BE468 Keypad Lock Encoding:

To begin encoding this type of lock, enter the default factory code (usually 1234) followed by the “#” symbol. Then press 1 for Programming Mode, and 6 for Setting User Codes (or 7 if you want to set up Time Schedules).

Enter your desired four-digit or eight-digit user code twice (for confirmation), followed by the “#” symbol again. The last step is to press “*,” which will save your changes in memory and exit out of Programming Mode.

4 easy steps to Reset your Schlage keypad Lock:

Resetting your Schlage keypad lock is relatively straightforward and requires just a few steps:

1 – Locate the Reset Button:

The first step to resetting your Schlage keypad lock is to locate the reset button. This button is usually located on the back of the device and will have an “R” printed or near it.

2 – Enter Your Current Code:

Once you’ve identified the reset button, enter your current code into the keypad lock. Ensure you enter it correctly; if you enter an incorrect code three times in a row, your code will be locked out for 30 minutes. 

3 – Press and Hold the Reset Button:

After entering your current code, press and hold the reset button until you hear a beep sound, the light above the keypad should start blinking to confirm that your lock has been successfully reset. 

4 – Enter Your New Code:

Finally, please enter your new code and make sure it’s entered correctly; you don’t want to get locked out again! Once you’ve verified it’s correct, press any number before entering again so the light stops blinking and stays on continuously. And that’s all, your Schlage keypad lock is now ready for use with its new code.

Unlock the Possibilities of Schlage Keypad Codes:

Two types of Schlage keypad codes can help you unlock the possibilities of convenience and security.

Let’s break down the differences between the two and explain what you need to do to keep your keypad locked securely.

1 – Single-Use Access Codes:

Single-use access codes are used when you want someone to be able to enter your home without giving them a permanent code. These codes can be set up for a specific time or just one use.

After they have been used, they automatically delete themselves from the system. These codes are ideal if you have guests visiting who don’t need a long-term code or if you need to give someone access temporarily.

2 – Master Keypad Codes:

Master keypad codes are used when you want someone to have long-term access to your home. These codes can be set up so that they never expire and don’t have any restrictions on when they can be used.

Master keypad codes should only be given to trusted individuals who need frequent access to your property. It is also important to note that these codes cannot be changed once they have been created, so it is essential that you choose them carefully and ensure that only the intended people know them.

Methods to Reset Your Schlage Encoded Keypad Lock:

It’s a common problem. You’ve been using your Schlage-encoded keypad lock for years, and suddenly it stops working. Maybe you’ve forgotten the combination, or it’s just malfunctioning. It’s not the end of the world; you can quickly reset your Schlage encoded keypad lock.

Method of Resetting the Encrypted Keypad Lock:

Follow below mentioned steps for resetting Encrypted keypad lock:

1 – Remove the Battery Pack

The first step to resetting your Schlage keypad lock is to remove the battery pack. To do this, unscrew the screws on either side of the door handle and pull out the battery pack.

Next, disconnect the wires from the battery pack and set them aside. Make sure not to touch any of the exposed wires because this could cause an electrical shock or short circuit.

2 – Resetting the Lock

After disconnecting the battery pack, you’ll need to reset your lock by pressing down on both sides of the cylinder for five seconds until you hear a click sound.

At this point, your lock should be successfully reset and ready to accept a new code.

3 – Entering Your New Code

Now it’s time to enter your new code into your Schlage lock! To do this, simply press down on both sides of the cylinder again until you hear a single beep sound. This will activate programming mode, which allows you to enter a new four-digit code of your choosing via the keypad on top of the door handle.

Once you have entered all four digits, press down on both sides of the cylinder again until you hear two beeps indicating that programming mode has been deactivated and your new code has been saved successfully. Also learn the method of resetting your Kwikset Lock.

Step-by-Step Guide to Change Your Schlage Lock 4 Digit Default Code:

You will want to change the default code if you have recently installed a new Schlage lock. This code is usually set to the same four digits and can be easily adjusted using the lock’s interface.

1 – Prepare Your Lock for Code Changing

Before you begin changing your code, make sure that your lock is in its unlocked position. If it is currently locked, use the original factory-set code to unlock it.

Once it is unlocked, press down and hold the “Schlage” button at the top of the keypad until all its lights start flashing simultaneously.

2 – Enter Your New 4-Digit Code

Once the lights start flashing on your keypad, enter the new four-digit code you want to use with your Schlage lock. Make sure that you remember this new code, as it will be used for future unlocking attempts.

Once you have entered your new four-digit code into your keypad, press down and hold both the “Schlage” and “Lock” buttons at the top until its lights stop flashing.

3 – Test Your New Code 

To confirm that your new four-digit code has been successfully saved onto your Schlage lock, try using it to unlock it; if everything was done correctly, then it should work!

If not, try repeating Steps 1–3 again or consulting with a professional locksmith for assistance if necessary.

Read the method of kwikset 909 resetting.

How to Change the Default Programming Code on a Schlage Lock:

To ensure your home and property stay safe and secure, you should regularly change the default programming code on your Schlage lock. Read on to learn how!

1 – Prepare Your Lock

Before starting this process, gather all the supplies you’ll need for this job. You will need:

• A flathead screwdriver.
• A paperclip or similarly thin object.

Ensure that the batteries in your Schlage lock are fresh and functioning properly so you don’t run into any issues while changing the codes.

2 – Access Your Lock’s Programming Mode

Once your tools are ready, press the small reset button at the bottom of your lock with a paperclip or similarly thin object. This will put your Schlage lock into its programming mode so you can start changing its settings.

3 – Enter Your New Code

Now that your Schlage lock is in programming mode, use the keypad to enter a new 6-digit code of your choice. For maximum security, we recommend using something completely random like 823541 or 598103 (make sure not to forget it!).

Once entered correctly, press “A” or “B” depending on which type of Schlage locks you have; this will save and store your new code onto the system memory.

4 – Test Out Your New Code

Test your new code by entering it into the keypad and turning the knob clockwise to unlock it. If successful, then congratulations! You have successfully changed the default programming code on your Schlage lock.

Make sure to remember this new code as it is now what protects both you and anyone else who needs access from being locked.

Reset a schlage keypad lock FAQS